Facilities and services
From design to finished part or equipment, all in one place: we design, forge, heat treat, cut, machine, weld, automate and test special alloys. A single point of responsibility for the part, from material to certificate.
Engineering
Application engineeringAlloy selection by temperature, pressure and corrosive medium, failure analysis, purchase specification review and equivalents between standards
Mechanical designMechanical design of pressure vessels, heat exchangers, tanks and parts to drawing
Automation and controlAutomation of the equipment Dustre builds
Forging
Heat treatment
Heat treatmentQuenching, tempering, normalizing, annealing, solution annealing, aging and stress relief of alloy steels, stainless, duplex and nickel alloys
QuenchingQuenching of alloy steels and martensitic stainless
TemperingTempering after quenching to adjust the hardness and toughness of alloy steels and martensitic stainless, per the standard or the specified hardness
NormalizingNormalizing of forged carbon and alloy steels
AnnealingAnnealing to soften the steel, improve machinability and eliminate stresses, with controlled slow cooling in the furnace
Solution annealingSolution annealing of austenitic stainless, duplex, super duplex and nickel alloys
AgingAging (precipitation hardening) of 17-4PH, 15-5PH, Inconel 718, Monel K-500 and A-286 in the H900 to H1150 conditions
Stress reliefStress relief of welded, fabricated and machined parts to reduce distortion, cracking risk and stress corrosion cracking
Cutting
Cutting of steel and special alloysCutting of plates, bars, pipes and blocks in stainless, duplex, nickel alloys and titanium by waterjet, laser and band saw, to the size of your order
Waterjet cuttingAbrasive waterjet cutting of plates and blocks in stainless, duplex, nickel alloys and titanium, without heating the part and without a heat-affected zone
Laser cuttingLaser cutting of carbon steel, stainless and special alloy plates with high precision, clean edges and repeatability for series parts
Band saw cuttingBand saw cutting of bars, pipes, billets and blocks in stainless, duplex, nickel alloys and alloy steels, to the size of the order
Machining
MachiningMachining of parts in stainless, duplex, nickel alloys and titanium
TurningTurning of shafts, flanges, rings, bushings and discs in special alloys, with roughing and finishing to drawing
MillingMilling of blocks, plates and prismatic parts in stainless, duplex, nickel alloys and alloy steels, to drawing
DrillingDrilling of flanges, heat exchanger tubesheets and plates in stainless, duplex, nickel and other special alloys, per ASME standard or customer drawing
Metal fabrication, forming and welding
Metal fabricationMetal fabrication in stainless, duplex and nickel alloys
FormingForming of steel and special alloy plates and bars at Dustre
Plate bendingBending of carbon steel, stainless and special alloy plates on a press brake, with radius and angle to drawing, for fabrication and plate parts
Plate rollingRolling of carbon steel, stainless and special alloy plates for cylinders, shells, rings and equipment casings
Welding: laser, TIG and MIG/MAGLaser, TIG and MIG/MAG welding of stainless, duplex, nickel alloys and alloy steels, with the right consumable for each alloy and for dissimilar joints
Testing laboratory
Testing laboratoryDustre testing laboratory
PMI: positive material identificationPMI (positive material identification) confirms the alloy of stainless, duplex, nickel alloys and alloy steels by composition, without damaging the part
Tensile testTensile test to measure yield strength, tensile strength, elongation and reduction of area of steels and special alloys
Hardness testBrinell, Rockwell and Vickers hardness testing of steels, stainless and special alloys, to check heat treatment and NACE MR0175 limits
Charpy impact testCharpy V-notch impact test, including at low temperature, to measure the toughness of steels, duplex and welds
Frequently asked questions
Does Dustre work on customer-supplied material?
Yes. Machining, cutting, heat treatment, welding and testing can be done on material you supply, as long as the alloy and the specification are defined.
What is the maximum part size?
It depends on the process. Send the drawing with material and quantity and we reply with process, capacity and lead time.
Have a drawing?Send the drawing, alloy, quantity and standard. We reply with process, lead time and price.
Request a quote